ESTREL ESHOOTER MOSFET ETU ADVANCE FOR AEG V2 REAR WIRING

Features of the ESTREL ESHOOTER MOSFET ETU ADVANCE FOR AEG V2 REAR WIRING.

• 7 modes to choose from: Safe, Semi-Auto, Binary, Burst, Aug, Full Auto and Sniper.
• Allows pre-cocking for better and faster trigger response.
• Real magazine simulation. After 30 rounds, the magazine must be reinserted.
• Adjustable ROF.
• Protection against over-discharge and low batteries.
• Active braking and cycle detection protects your gears and gearbox.
• Remote firmware updates via the Eshooter app.
• The smart fuse protects the battery, motor and controller from overheating, overloading and short circuits.
• Standby charging after one hour to avoid unnecessary battery drain.
• Locked rotor protection will alert the user if the gears and motor are not operating properly.
• Sensor calibration to ensure maximum performance.

The Kestrel V2 ETU is compatible with the standard Tokyo Marui V2 gearbox. It makes your AEG much smarter, more reliable, and more responsive. Customize your AEG's firing parameters by connecting the "Eshooter" app for a different shooting experience.

Trigger Sensitivity Adjustment: Five sensors detect trigger movement and control its sensitivity. Connect to the Eshooter app wirelessly, without disassembling your weapon.

Selection Modes: Two selectors allow your game to use different selection modes, including:

• Safe Mode can prevent your weapon from firing, regardless of where the selector switch is located.
• Semi mode allows you to fire a bullet in one go.
• Binary mode allows you to pull the trigger to fire one shot and release it to fire again.
• Burst mode allows you to preset the number of balls fired.
• Aug mode allows you to lightly press the trigger (depending on your trigger sensitivity setting) for one shot, then press continuously to switch to AUTO mode.
• Auto mode allows you to take pictures continuously until the trigger is released
• Sniper mode can be used with the sniper delay function, simulating 2-stage safety and recoil

Pre-cocking: Pre-cocking simulates the trigger response of a real weapon. It allows the spring to pre-compress to speed up the response. You can adjust the pre-cocking settings before you begin. Pre-cocking can be used in all the modes mentioned above.

Real Magazine: Simulate a real 30-round magazine for a more realistic gaming experience. After 30 shots, the magazine must be reloaded.

Rate of Fire Control: Allows you to adjust the AEG's rate of fire to achieve the desired rate of fire.

Battery Protection: LiPo and LiFe batteries are very sensitive to over-discharge. To prevent damage due to over-discharge, the microprocessor prevents firing when the voltage drops to a critical level.

Low Battery Warning: When the voltage drops to a critical level, the app sends a low battery notification and the AEG will not fire.

Active Brake: The adaptive active brake function prevents gearbox instability, ensuring the piston stops in the forward position to reduce unnecessary stress and extend the life of the gearbox and internal parts.

Cycle Detection: The Kestrel V2 detects the end of the cycle thanks to its speed sensor which counts each tooth. You can choose between DSG (9:1), SSG (13:1) and standard (18:1) speeds.

Firmware Updates: You can update the firmware remotely via the Eshooter app, which supports free OTA service.

Smart Fuse: The Kestrel V2 is equipped with two fuses, a mini smart fuse and an automatic fuse, with a maximum current of 25A. They protect the battery, motor, and controller, even if the battery is connected incorrectly. It also protects the MOSFET from overheating, overloading, and short circuits, preventing damage to the motor and battery in the event of your weapon jamming.

Sleep Mode: The ETU goes into sleep mode after one hour of inactivity of your weapon, preventing the battery from discharging.

Locked Rotor Protection: The rotor is automatically locked. The Kestrel V2 provides active protection and reminds users to check the gearbox to avoid damage due to gear and motor malfunction, or overcurrent.

Sensor Calibration: Kestrel V2 provides a sensor calibration function to ensure your ETU sensors maintain the best performance and give you a more accurate shooting experience.

Manufacturer: Eshooter

Features:

Dimensions (mm): 47.4 x 28.7 x 13.5 Voltage range: 3.75V - 17V Current consumption: 17 mA Temperature range: -15 + 50 degrees Calvin relative humidity: ≤ 80% Compatibility: Fits Tokyo Marui Spec Version 2 Airsoft AEG Gearboxes Package Includes: MOSFET Kit, 2 x 0.2mm Shims, 8 x 0.3mm Shims, 8 x 0.5mm Shims, 2 x Plum Blossom Metal Gaskets, 2 x M2x4 Screws, 1 x Deans Connector, 2 x Heat Shrink Tubing, 2 x Double-Sided Tapes, 2 x 2.6*14 Screws, 1 x Charger Button Base, 1 x 30A Fuse, Manual

Disclaimer: Professional installation highly recommended. Please use your best judgment when installing custom parts as fit and compatibility may vary. Modifications may be required. Professional installation recommended.